Every safety recall published by the Australian government, searchable and filterable.
Due to a manufacturing defect, the battery wiring harness may chafe against the battery holder bracket. This may cause an internal short circuit leading to a vehicle fire.
On the affected vehicles, the rear lower suspension arm bolt may not meet the required specification and may detach. As a result, the suspension could collapse and/or damage the br…
The gearshift fork spiral pin may dislodge and move out of position leading to an internal transmission failure. If this occurs, it could result in an unintended vehicle movement.
The Exhaust Gas Recirculation (EGR) valve may fail. If this occurs, it could lead to reduced acceleration, engine vibration and/or a loss of motive power whilst driving.Note: A war…
Due to a manufacturing defect, the fuel control valve in the high-pressure fuel pump could allow excess fuel to enter the pump. If this occurs, the engine could stall resulting in…
Vehicles that are fitted with a Combined Charging System (CCS2) charge port may experience increased electrical resistance during high-power Direct Current (DC) fast charging causi…
The rear centre seat belt anchor buckle may have been incorrectly assembled. As a result, the seat belt may not properly latch or operate as intended.
Due to a manufacturing issue, the handlebar bolt may not have been fastened with sufficient torque and could become loose. This could lead to a loss of vehicle control whilst ridin…
The gearshift fork spiral pin may dislodge and move out of position leading to an internal transmission failure. If this occurs, it could result in an unintended vehicle movement.
Due to a software issue, the cell modules installed in the high voltage battery may overheat at high charge levels. If this occurs, it could lead to cabin smoke or a vehicle fire.N…
Due to a software issue, the cell modules installed in the high voltage battery may overheat at high charge levels. If this occurs, it could lead to cabin smoke or a vehicle fire.N…
Due to a manufacturing defect, the worm wheel within the Electronic Power Steering system (EPS) may have been insufficiently lubricated. This may result in a sudden increased steer…
Due to a design issue, the second-row seat recliner mechanism may not fully engage during seat back adjustment. As a result, the seat back could move inadvertently.
Due to a manufacturing defect, the panoramic roof glass panel bonding may have insufficient adhesion. As a result, the panoramic panel could detach from the vehicle.
Due to a manufacturing defect, the rear middle seating position may not have been fitted with a child restraint anchor point as required by Australian Design Rule (ADR) 34/03 - Chi…
Due to a design issue, the steering knuckle arms, first steer axle spring mounts and suspension pin shafts may not meet the required specifications. This could result in excessive…
Due to a software error, the Instrument Cluster may display a blank screen or may not operate as intended.
Due to a software issue, the headlamp low/high beam may not have been adjusted according to specifications. As a result, the headlamps could cause excessive glare to oncoming traff…
The air conditioning (A/C) wiring harness may become damaged during routine microfilter (cabin air filter) replacement. This may cause an internal short circuit, which could lead t…
Due to a manufacturing defect, the ball pins in the steering rod assembly may not have been properly hardened, reducing durability. This can cause the pins to fracture and separate…
Due to a design defect an electrical connector within the alternator main wiring harness may develop a high resistance condition. This can cause excessive heat and lead to a loss o…
Due to a manufacturing defect, the Exhaust Gas Recirculation (EGR) cooler may develop an internal coolant leak. If this occurs, the leaking coolant and recirculated exhaust gas ma…
The vehicle's owner manual contains incorrect information regarding the location of the child seat top tether anchor point. As a result, the user may not be able to locate the appr…
Due to a manufacturing defect, the inner frame edge of the front seats may have been produced with improperly finished surfaces. As a result, the frame edge could damage the side a…
Due to a manufacturing issue, the cell modules installed in the high voltage battery may overheat at high charge levels. If this occurs, it could lead to a vehicle fire.Note: Keep…