Every safety recall published by the Australian government, searchable and filterable.
Due to a manufacturing defect, inadequate sealing of the starter motor may allow moisture to enter into the unit. If this occurs, corrosion may result in the engine not starting.In…
Due to a manufacturing issue, under certain driving conditions the upper triple clamp that secures the handlebar may fracture. This could lead to a loss of vehicle control whilst r…
Due to a manufacturing defect, the front passenger and/or driver seatbelts may not meet the required specifications. As a result, the seatbelt(s) may not operate as intended in the…
Due to a manufacturing defect, the fuel pipe may become damaged over time, caused by vibration and extended high RPM usage. If this occurs, fuel may leak potentially causing a loss…
Due to a supplier manufacturing defect, the high-pressure fuel pump may not have been fastened to the cylinder head with sufficient torque. As a result, fuel may leak, and in the p…
Due to a software issue, the electromechanical brake servo control unit may switch off. As a result, the braking assistance could be reduced, requiring greater pedal force and pote…
Due to a manufacturing defect, the Body Control Module (BCM) may be susceptible to water ingress. As a result, the front and rear side marker lamps, taillamps, and license plate la…
Due to a software issue, when the vehicle starts the Instrument Panel Cluster (IPC) may fail to illuminate visual critical safety information upon start-up.
Due to a manufacturing defect, the rear wheel hub bolts may become loose or break causing damage to the wheel axle and axle hub splines over time. This could result in the vehicle…
Due to a software issue, the vehicle may accelerate without the pedal being depressed. This may result in unintended vehicle movement.
Due to a software programming issue of the Body Control Module (BCM), the instrument cluster fuel level may not operate as intended. This may result in an incorrect display of fuel…
Due to the programming of the Heating, Ventilation, and Air Conditioning (HVAC) control ECU software. Under certain conditions, such as a specific failure mode of the electric comp…
The rear wheel shaft could lose its structural integrity and, in extreme cases, break whilst riding.
Due to a software issue, the brake boost function may not operate as intended. As a result, braking could be reduced requiring greater pedal force and potentially increasing the ve…
The dipstick provided with the vehicle may not meet manufacturing specifications. As a result, the level of engine oil may be too low to feed the main bearings in the engine.
Due to a manufacturing defect, the tow bar hitch may not have been welded to the required specifications and could detach from the tow bar whilst driving.Note: Whilst towing a cara…
Due to a manufacturing defect, the electric heater element within the Heating Ventilation Air Conditioning (HVAC) system may deteriorate over time. If this occurs, the windscreen d…
Due to a software programming issue, the Heating Ventilation Air Conditioning (HVAC) electrical compressor may fail. If this occurs, the windscreen defrost function may not operate…
Due to a software programming issue, the Heating Ventilation Air Conditioning (HVAC) electrical compressor may fail. If this occurs, the windscreen defrost function may not operate…
Due to a manufacturing defect, the wiring harness connected to the handlebars may become damaged over time. If this occurs, the horn and/or the headlights may not operate as intend…
The front gooseneck of the trailer may have insufficient reinforcement and could crack. If this occurs, it could lead to a loss of trailer control and/or detachment from the tow ve…
A software error may cause the vacuum pump to malfunction. As a result, braking assistance could be reduced, requiring greater pedal force and potentially increasing the vehicle’s…
Due to a manufacturing defect, the fuel pump impeller may become deformed under certain environmental conditions, interrupting the fuel supply. If this occurs, the engine could sta…
Due to a design defect, fuel spilled into the fuel filler pocket whilst refuelling can come in contact with an ignition source resulting in a vehicle fire.Note: General Motors advi…
Due to a programming issue, the Light Emitting Diode Driver Control Module (LDM) may fail. As a result, high beam, low beam, position lamps and daytime running lamps may not operat…