Every safety recall published by the Australian government, searchable and filterable.
During the manufacturing process, the Restraint Control Module (RCM) was loaded with an incorrect configuration. As a result, if an incorrect replacement part is installed in the s…
Due to a manufacturing defect, the starter motor solenoid switch can experience increased wear that could cause an internal short circuit. If this occurs, the driver may be unable…
Due to a software issue, the brake fluid warning light may not illuminate as intended to warn the driver if the brake fluid level is low. As a result, insufficient brake fluid coul…
Due to a software issue, under certain circumstances if the battery level drops below a critical threshold, the transmission may shift into Park when the vehicle is travelling at s…
Due to a potential fault in the Light Emitting Diode (LED) Driver Control Module (LDCM) this module may fail. As a result, high beam, low beam, position lamps and daytime running l…
Due to a manufacturing defect, the rear brake hose could be susceptible to heat damage and may result in a sudden loss of rear braking performance. The front brake will continue to…
Due to a manufacturing defect, the Electronic Control Unit (ECU) wiring harness may chafe against the engine mounting bracket and become damaged. As a result, this could lead to a…
Due to a manufacturing issue, the wiring harness under the front seats may not have been positioned according to specifications. As a result, it may become damaged over time and af…
Due to a manufacturing defect, moisture may enter the rear light bar assembly unit. This can cause the reverse lamps to become inoperative or to flicker intermittently.
Due to a manufacturing issue, the cell modules installed in the high voltage battery may be defective and could overheat. If this occurs, it could lead to a vehicle fire. The range…
Due to a manufacturing defect, the transmission wiring harness may chafe against the front drive shaft and become damaged. This could lead to a sudden loss of motive power whilst d…
Due to a manufacturing defect, the rear tyre steel belt may become damaged under certain off-road conditions or riding extended periods with low tyre pressure. This can lead to a l…
Due to a software issue, the Instrument Panel Cluster (IPC) may fail to illuminate the visual vehicle speed, lane keep assist and Advanced Emergency Brake System (AEB deactivation…
Due to a manufacturing defect, the left-hand rear drive shaft may have been incorrectly installed. As a result, it could lead to a loss of motive power whilst driving and/or uninte…
Due to a manufacturing issue, the cell modules installed in the high voltage battery may overheat at high charge levels. If this occurs, it could lead to a vehicle fire.Note: Keep…
Due to a manufacturing defect, the Occupant Restraint Controller (ORC) module may disable the Electronic Stability Control (ESC). If this occurs, the ESC may fail without warning r…
Due to a manufacturing issue, the cell modules installed in the high voltage battery may be defective and overheat during charging. If this occurs, it could lead to a vehicle fire.…
Due to a manufacturing defect, the power steering pump O-ring seal may have been damaged allowing fluid to leak. If this occurs, it could lead to increased steering effort resultin…
Due to improper assembly, the indicator and rear lamp control switch wiring harness may become damaged due to vibration which could cause an internal short circuit. If this occurs,…
Due to a manufacturing defect, the left rear seat belt retractor mechanism may not operate as intended. As a result, excessive belt lengths may be released in the event of an accid…
Due to a manufacturing defect, the shielding ring in the high voltage wiring harness may not be properly grounded. This can reduce the effectiveness of electromagnetic shielding, w…
Due to a manufacturing defect, the left rear seat belt retractor mechanism may not operate as intended. As a result, excessive belt lengths may be released in the event of an accid…
Due to a manufacturing defect, the 12-volt battery vent may not operate as intended. As a result, under certain driving conditions such as high temperatures toxic gases may leak in…
Due to a manufacturing issue, the cell modules installed in the high voltage battery may be defective, which could cause an internal short circuit. A short circuit could result in…
Due to a manufacturing issue, oil may leak past the engine piston rings. If this occurs, the engine could stall causing the rear wheel to lock leading to a loss of motive power and…